Devry project math 265 project

at
Categories
Tags

Do you have the solution for this project?

Math265 Project Part B

Name:

In this part of the project, you will model the behavior of a resistor-inductor (RL) circuit in a transient state.

Initially, the DC voltage source is off and there is no current in the circuit.After the source ‘ε’ is turned on, the current through the inductor quickly rises and produces an EMF that opposes the change in current:

where ‘L’ is the inductance

Using Kirchhoff’s Voltage Law and Ohm’s Law results in the equation

This differential equation can be solved to determine an expression for the current through the circuit as a function of time:

whereis the final current andis known as the inductive time constant.

The theoretical EMF produced by the inductor can be found as follows:

Graphing Current vs Time (25 points)
Consider an RL circuit that is being charged with a voltage source ε.The voltage across the inductor is shown as a function of time in the table below, with time in seconds (s) and voltage in volts (V).The magnitude of the current at time tf can be determined from the voltage (v) as

where I(ti) is the current at time ti.We will use a technique to calculate this integral algebraically, to determine the current from the voltage. By doing so, we are finding the approximate area under the voltage versus time curve.To determine the current at a time ‘2’, where time ‘1’ is the previous interval, use

The numerator is the average voltage multiplied by the time interval and is an algebraic approximation for the area underneath the voltage versus time curve between t1 and t2.

In this example, for each interval, .Referencing the voltage in the table below, to determine the current for the first cell and knowing that at time t=0s,

and for the next cell

Repeat the process to fill in all of the cells in the table maintaining 3 significant figures for the current.

Time (s)

Voltage (V)

I(A)

0.0E+00

5.00

0

3.0E-07

2.74

0.00116

6.0E-07

1.51

0.00180

9.0E-07

0.83

1.2E-06

0.45

1.5E-06

0.25

1.8E-06

0.14

2.1E-06

0.07

2.4E-06

0.04

2.7E-06

0.02

3.0E-06

0.01

Open Desmos by copying and pasting the following link into your web browser or use control+click(https://www.desmos.com/calculator/lhdbhowyyh). Enter the data from the table for current in the column ‘y1’.

You will fit the data using the theoretical equation for current as a function of time.

Adjust the fitting parameters ‘a’ and ‘b’ using the sliders so that the curve matches the points.Since we are using an approximating method for calculating the points, the curve will not be an exact match. To fit the curve as well as possible, note the R2 value.R2 is known as the coefficient of determination.It is a unit-less number between 0 and 1 and indicates how well the curve fits the points.The closer R2 is to 1, the better the fit.Adjust ‘a’ and ‘b’ so that R2 is as close to 1 as possible

Record your fitting parameters below as well as your R2 value:

a=

b=

R2=

Comparing to the equation for current above, noting thatand given that , determine the resistor value.Show your work

R=

Noting that , determine the value of the inductor.Show your work.

L=

Take a screenshot of Desmos showing current versus time and your data and paste below.

Screenshot of Desmos

Graphing Voltage vs Time (25 points)
The magnitude of the voltage across the inductor was shown to be

where

Open Desmos by copying and pasting the following link into your web browser or use control+click(https://www.desmos.com/calculator/g3dkvlljti)

Using Desmos and the quantities R, L and ε from Section I., plot the voltage as a function of time, using the equation above.In Desmos, type the values for ε, R and L to replace the # symbols in the equation provided.

Copy and paste your graph with the theoretical voltage versus time below.

Screenshot of Desmos:

Summary of Section I (10 points)
Write a two paragraph summary of your findings from Section I.Explain the setup and the results.

Section I Summary

Summary of Section II (10 points)
Write a two paragraph summary of your findings from Section II.Explain the setup and the results.

Section II Summary

Sample Solution

Generations children have been brought up playing with the famous Barbie and Ken Fashion dolls. Barbie was the first doll that displayed the perfect body, waist size 0, skin colour, and long sleek hair enforcing unrealistic beauty norms (Unknown 2017).The doll received criticism from parents and media regarding the unrealistic beauty expectations targeted at young children, yet Mattel Inc. the owner of Barbie, sold over a billion dolls making Barbie the company’s largest and most profitable line (Unknown 2017). In 2006, a study from the University of Sussex found that thin and fair dolls like Barbie created negative and harmful body perceptions for young girls and led to low self-esteem (Unknown 2017). In the study, all 162 participants reported the desire to look like Barbie and had embodied the unrealistic beauty norms (Unknown 2017). However, after being the center of controversary for many years, Mattel Inc. rebranded Barbie and released a new commercial that spreads a positive, less superficial, and more realistic message about beauty (Bondareff 2010). The commercial encourages young children to be or do anything without worrying about the social beauty norms. Mattel Inc. created a doll with dark skin complexion and black dreadlocks breaking the chain of blonde and fair Barbie dolls (Bondareff 2010). Although Mattel Inc. has taken steps towards changing the unrealistic beauty perceptions by creating diverse dolls with different hair textures and skin colours, the doll still pursues the skinny body image (Bondareff 2010).

This case is significant for development of this research question as it demo

This question has been answered.

Get Answer